Audi A4, S4

Since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
- Controls and receptions of safe operation
   Controls and devices
   Information system of the driver (FIS)
   Unlocking and car lock-out
   Illumination and review maintenance
   Seats and niches
   Heater, ventilation and air conditioner
   Automatic transmission (АТ)
   Communication and navigation
   Universal remote radio management HOME LINK
   Safety systems
   Features of operation and auxiliary systems
   Обкатка
   Trailer towage
   In case of emergency
   Car refuelling
+ Current leaving and service
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Information system of the driver (FIS)

The general data

The information system of the driver (FIS) is car information centre.

FIS is information centre of your car. The given system easily and quickly informs you concerning a current technical condition of the car. For example, you can learn run before the next maintenance service for the purpose of performance of repair-preventive works and many other things. Besides, at a corresponding complete set of the car the driver can obtain the given radio systems, phone, telematics and navigation system.

On cars with system навигации* Audi or Audi телематик* the information image on the display is multi-colour and possesses the raised resolution.

Indication of information system of the driver is deduced on located in the centre of a control panel the display.

The control panel display:

— Radio indication;
— Indication of external temperature;
— A course stock on fuel.

On cars with automatic transmission the information is deduced on the display only after inclusion of a range of movement.

Standard execution of a control panel

The information on a current operational condition of the car is deduced on located in the centre of a control panel the display.

Radio indication — Information system of the driver (FIS)

Indication of external temperature — Information system of the driver (FIS)

Course stock on fuel — Information system of the driver (FIS)

The prevention of not closed door and luggage carrier - Information system of the driver (FIS)

Positions of the lever of the selector 5 step automatic transmissions — Automatic transmission (АТ)

Positions of the lever of the selector multitronic — Automatic transmission (АТ)

The alarm system of excess of speed — Information system of the driver (FIS)

System контролей malfunctions — Information system of the driver (FIS)

Instructions to the driver — Information system of the driver (FIS)

The prevention of the tightened manual brake — Information system of the driver (FIS)

Indication of term of maintenance service — Controls and devices

Information system of the driver with the travelling computer

Radio indication — Information system of the driver (FIS)

Indication of external temperature — Information system of the driver (FIS)

The prevention of not closed door and luggage carrier — Information system of the driver (FIS)

Positions of the lever of the selector 5 step automatic transmissions — Automatic transmission (АТ)

Positions of the lever of the selector multitronic — Automatic transmission (АТ)

The alarm system of excess of speed — Information system of the driver (FIS)

System контролей malfunctions — Information system of the driver (FIS)

Instructions to the driver — Information system of the driver (FIS)

The prevention of the tightened manual brake — Information system of the driver (FIS)

Indication of term of maintenance service — Controls and devices

Malfunction of function of lamps — Information system of the driver (FIS)

The travelling computer — Information system of the driver (FIS)

Radio indication

At absence after the control the name of radio station or a radio frequency with the additional information appears the monitoring system of malfunctions of display of faults of 2nd degree of a priority and the included radio (depending on a radio complete set) after indication ОК will go out, on the display.

The given indication is the additional information of the radio display.

Indication of external temperature

Indication of external temperature is deduced on the display at the included ignition. On cars with automatic transmission indication appears only after inclusion of a mode of movement.

At temperatures from +5С to-5S to the left of temperature indication the snowflake is highlighted. Occurrence of a symbol in the form of a snowflake warns the driver about necessity of extra care in view of danger of ice. On the motionless car or at movement with very small speed indication can be a little above actual temperature owing to heat radiated by the engine.

On cars with the conditioner at display switching on indications under the Fahrenheit scale (F) accordingly indication of external temperature, the Heater, ventilation and air conditioner automatically changes.

At a conclusion to indication of the data of system of navigation (support to the purpose) indication of external temperature appears in the second line of the display panel of radio.

Course stock on fuel

The given indication helps at planning.

On the display indication of a stock of a course on fuel in km is deduced.

The given indication shows, how many kilometres your car still can pass on the actual rest of fuel in the given mode of movement. The course stock on fuel is defined by the discrete values counted by steps on 10 km.

The expense of fuel on the last is accepted to a basis of calculations of a stock of a course of 30 km of a way. At more economic subsequent movement the course stock increases.

The prevention of an open door and luggage carrier

The display: the prevention of an open door and a luggage carrier

The pictogramme is deduced on indication if at the included ignition are not closed at least one door, a cowl or a luggage carrier. The pictogramme specifies also, what door or doors are not closed, as an example the door of the driver and the right back door are shown.

Represented on the pictogramme of the display the cowl or a luggage carrier blink, if they are not closed. Right after full closing of all doors, a cowl and a luggage carrier the given pictogramme dies away.

Indication of the pictogramme warning about an open door and a luggage carrier, cars with information system of the driver and travelling компьютером* it is possible to disconnect short-term pressing of command keys by the travelling computer. However the pictogramme will appear at once again after change of position of doors, a cowl or a luggage carrier.

The monitoring system of malfunctions

Introduction

The display: the monitoring system of malfunctions

At the included ignition and during movement the system of the automatic control of malfunctions continuously supervises certain functions and a technical condition of systems of the car.

Or about necessity of urgent performance of repair-preventive works the system informs on arising malfunctions a sound signal, accompanying its red and yellow light symbols of the display of a control panel depending on priority degree.

Red symbols signal about danger, and yellow are alarm symbols. Besides, in certain situations, in addition to red symbols there are instructions to the driver.

Instructions to the driver

In addition to control lamps and symbols on the control panel display instructions to the driver are deduced.

At occurrence of the message on malfunction of function of a lamp after the control of function of lamps, at movement with the tightened manual brake, and also before inclusion of a mode of movement of cars with automatic transmission on the display corresponding indication of the instruction to the driver is deduced.

Besides, at a blinking on the display of any symbol of the first degree of a priority, the driver can deduce corresponding instructions on indication.

Conclusion to indication of instructions to the driver

For example, on the display there is a symbol of infringement of function of pressure of impellent oil. If you press now button "СНЕСК" on the display there will be a following instruction:

Motor abstellen, lstand prfen (to muffle the engine to check up oil level)

The given indication of the display dies away approximately later 5 seconds. Short-term pressing of button "СНЕСК" the instruction can be deduced on indication.

Instructions Handbremse angesolen (tighten a manual brake) and Beim Einlegen einer Fahrstufe im stand fussbremse betatigen (at a choice of a mode of movement of the motionless car press a brake pedal) cannot be deduced on indication repeatedly. The given instructions die away after removal of the car from a manual brake or inclusion of a mode of movement.

The prevention of the tightened manual brake

 PERFORMANCE ORDER

  1. Remove the car from a manual brake.

At movement on rashness with the tightened manual brake buzzer sounding (a sound signal) is distributed and on the display there is an instruction:

Handbremse angesolen (will tighten a manual brake)

The given prevention appears at movement more than 3 seconds with a speed more than 5 km/h.

Cars with a manual box of a gear change

The control of functions: a manual transmission

At inclusion of ignition the monitoring system of malfunctions carries out the automatic control of functions. If checked up by the monitoring system of malfunctions of function is perfectly in order, for some seconds indication ОК lights up.

Corresponding indication testifies to presence of malfunctions instead of indication ОК. The warning signal Simultaneously sounds.

In the absence of indication ОК, and also malfunctions, the monitoring system of malfunctions of the car is subject to check.

Cars with automatic transmission

The control of functions: automatic transmission

At inclusion of ignition the monitoring system of malfunctions carries out the automatic control of functions.

At a finding of the lever of the selector in position P or N on the display there is an instruction

Beim Einlegen einer Fahrstufe im Stand Fussbremse betatigen (at inclusion of a mode of movement of the motionless car press a brake pedal).

If now to include a movement mode (R, D etc.) the instruction dies away and the automatic control of functions is carried out. If under control functions are perfectly in order, in summary for some seconds indication ОК is highlighted.

In the presence of malfunctions, approximately in 15 seconds after engine start, the above-stated instruction to the driver is replaced by indication of a corresponding symbol of malfunction. The warning signal simultaneously sounds.

In the absence of indication ОК, and also malfunctions, the monitoring system of malfunctions of the car is subject to check.

Red symbols

The red symbol signals about danger.

The display: falling of level of a cooling liquid

 PERFORMANCE ORDER

  1. Stop.
  2. Muffle the engine.

Check up faulty function. If necessary take advantage of the qualified help.

BREMSE

Malfunction of brake system


KUHLMITTEL

Falling of level of a liquid in system of cooling or its overheat


OLDRUCK

Pressure drop of impellent oil

Red symbols specify in infringement of functioning of the first degree of a priority (danger).

At occurrence of a red symbol three following one after another is distributed

Precautionary sound signal. The symbol blinking proceeds before malfunction elimination. At occurrence at once several infringements of functioning of the first degree of a priority symbols appear consistently, with duration of indication of each of them of 2 seconds.

Malfunction of brake system

Eliminate malfunction of brake system as soon as possible.

The blinking on the symbol display means malfunction of brake system. In addition on the display indication of one of two instructions is deduced:

Fahrzeug anhalten Bremsfl. und Hudr.-l prfen

Vorsicht! Storung Bremse (ABS) Service aufsuchen

 PERFORMANCE ORDER

  1. Stop.
  2. Check up level of a brake liquid, Current leaving and service see the Head.

At refusal ABS control lamp ABS lights up together with a symbol of malfunction of brake system.

Malfunction of system of cooling

Urgently eliminate malfunction of system of cooling.

The overheat or falling of level of a cooling liquid can be the reason of a blinking of a symbol during movement. In addition on the display indication of the following instruction is deduced:

Motor abstellen und Kuhlmittel prufen (to muffle the engine and to check up level of a cooling liquid)

 PERFORMANCE ORDER

  1. Stop.
  2. Muffle the engine.
  3. Check up level of a cooling liquid, Current leaving and service see the Head.
  4. If necessary add cooling liquid, Current leaving and service see the Head.
  5. Continue movement only after the symbol will go out.
  6. If necessary take advantage of the qualified help.

If level of a cooling liquid in norm refusal of the fan of system of cooling can be the overheat reason.

If the control lamp of the category of the accumulator in addition burns, Controls and devices the reason can consist in breakage of a ridge belt see.

It is impossible to continue movement if the symbol specifies in malfunction of system of cooling - there is a danger of damage of the engine.

Low pressure of impellent oil

Urgently eliminate malfunction.

The blinking on the symbol display testifies to pressure drop of oil below norm. In addition on the display indication of the following instruction is deduced:

Motor abstellen lstand prfen (to muffle the engine to check up oil level)

 PERFORMANCE ORDER

  1. Stop.
  2. Muffle the engine.
  3. Check up level of impellent oil, Current leaving and service see the Head.
  4. If necessary take advantage of the qualified help.

Falling of level of impellent oil below norm

Add impellent oil at falling of its level below norm, Current leaving and service see the Head.

Normal level of impellent oil

It is impossible to continue movement if the symbol blinks at normal level of oil. Do not suppose also engine work idling - take advantage of the qualified help.

The control lamp of pressure of oil is not the index of its level in greasing system. Therefore check oil level regularly, is better at refuelling.

Yellow symbols

Yellow symbols are prevention symbols.

Models in standard execution

The display: a reserve stock of fuel

Reserve stock of fuel

Check up level of impellent oil

Malfunction of a sensor control of level of impellent oil

Deterioration of a brake overlay

The alarm system of excess of speed

Malfunction of dynamic regulation of an angle of slope of headlights

Yellow symbols signal about infringement of functioning of the second degree of a priority (prevention).

At occurrence of a yellow symbol one warning signal is distributed. Check up corresponding function. At at once several infringements of functioning of the second degree of a priority symbols appear consistently, with duration of indication of each of them of 2 seconds.

Models with FIS, the travelling computer

Reserve stock of fuel

Check up level of impellent oil

Malfunction of a sensor control of level of impellent oil

Deterioration of a brake overlay

The alarm system of excess of speed

Malfunction of dynamic regulation of an angle of slope of headlights

Falling below norm of level of a washing liquid

The alarm system of excess of speed 2

Deviations of pressure of the accumulator from norm

Malfunction of function of lamps

Yellow symbols signal about infringement of functioning of the second degree of a priority (prevention).

At occurrence of a yellow symbol one warning signal is distributed. Check up corresponding function. At at once several infringements of functioning of the second degree of a priority symbols appear consistently, with duration of indication of each of them of 2 seconds.

Reserve stock of fuel

If the given symbol lights up the first time it means that in a stock remains about 8-10 litres of fuel. Fill the car, car Refuelling see.

Check up level of impellent oil

At symbol occurrence check up oil level (the Head Current leaving and service) and if necessary add it.

Malfunction of a sensor control of impellent oil

At symbol occurrence check up the gauge of level of oil. Check oil level at each refuelling of the car by fuel (the Head Current leaving and service).

Deterioration of a brake overlay

At symbol occurrence check up brake Pads lobbies (and for one back) wheels.

The alarm system of excess of speed

Symbol occurrence means that actual speed has exceeded the entered value of speed. Lower speed.

Cars with the device of dynamic regulation of an angle of slope of headlights

Malfunction of the device of regulation of an angle of slope of headlights

Symbol occurrence means malfunction of the device of dynamic regulation of an angle of slope of headlights. Make repair of the device of regulation of an angle of slope of headlights.

Falling of level of a washing liquid

Symbol occurrence means necessity to add washing liquid in the refuelling tank glass - and фароомывателя *, Current leaving and service see the Head.

The alarm system of excess of speed

Symbol occurrence means that actual speed has exceeded the entered value of speed of the second degree of the prevention. Lower speed.

Deviation of pressure of the accumulator from norm

At symbol occurrence check up following components:

  • клиновой a belt
  • Pressure regulator
  • Accumulator condition

Remember also a control lamp of the category of the accumulator, Controls and devices see.

Malfunction of function of lamps

The monitoring system of function of lamps watches serviceability of lamps of the car.

At malfunction or lamp refusal on indication within first five seconds together with a symbol the explanatory text is deduced. For example, at infringement of function of the back left index of turn on the control panel display there is a following text:

Blinker hinten links (the back left index of turn)

In 5 seconds the given additional indication dies away. For a repeated call of indication quickly press button "СНЕСК".

Possible causes of infringement of function of a lamp:

Replace/repair connections in electroconducting and lamps накаливания.

The alarm system of excess of speed

Introduction

The alarm system of excess of speed allows to set restriction of speed which should not be exceeded.

The display: the alarm system of excess of speed

The alarm system of excess of speed warns the driver about excess of preliminary entered speed. As soon as actual speed will exceed the entered value approximately on 10 km/h, the warning signal is distributed. Simultaneously on the display there is an alarm symbol.

The alarm system of excess of speed allows to program two degrees of the prevention *, functioning independently from each other and carrying out not absolutely identical problems.

Despite presence of the device of the alarm system of excess of the programmed restriction of speed, supervise on a speedometer admissible rules the maximum speed.

Degree of the prevention 1: function

Value of degree of the prevention 1 can be changed during movement.

Degree of the prevention 1 gives the chance to set restriction of speed during movement. The entered value of speed remains in memory before ignition deenergizing if change of speed or cancellation of the entered restriction preliminary did not take place.

The alarm symbol of the first degree of the prevention appears on the display at excess of actual speed of the entered value. The symbol dies away at reduction of speed below the programmed value.

The symbol dies away, besides, at increase of speed approximately on 40 km/h above the entered value in a current a minimum of 10 seconds. Thus, however, there is no dump of the data of memory of the entered restriction of speed.

Degree of the prevention 1: programming

Degree of the prevention 1 is programmed by button SNESK.

Control panel fragment: button SNESK

Programming of restriction of speed

 PERFORMANCE ORDER

  1. The car should move with the set speed which should not be exceeded.
  2. Press and release button SNESK.

Cancellation of the entered restriction of speed

 PERFORMANCE ORDER

  1. Speed of the car should be more than 5 km/h.
  2. Press and keep more than 1 second button SNESK.

Successful input in memory proves to be true short-term fire on the display of an alarm symbol of restriction of speed at release buttons. The entered value of speed remains in memory before following short-term pressing of the button at other speed or while you pressing do not cancel more than 1 second the entered restriction.

Degree of the prevention 2: function

Value of degree of the prevention 2 can be changed only at the switched off ignition.

Degree of the prevention 2 gives the chance programming and cancellation of the maximum restriction of speed only at the switched off ignition. Programming of the given prevention is recommended in need of the general reminder to the driver of maintenance of certain maximum speed. For example, at movement in the country with restriction of speed, the maximum speed at movement with winter tyres. The alarm symbol of the second degree of the prevention appears on the display when actual speed will exceed the entered value. The symbol dies away, unlike degree of the prevention 1, only at decrease in speed below the programmed size.

Degree of the prevention 2: programming

Value of degree of the prevention 2 is programmed and cancelled established in the handle of a screen wiper by switches.

The screen wiper handle: the switch of functions

Programming of the maximum speed

 PERFORMANCE ORDER

  1. Switch off ignition.
  2. Press and release in a control panel button SNESK. Illumination of the counter of run and a digital watch joins.
  3. Press and keep a minimum of 2 seconds button SNESK. On the display there is an entered threshold value of the maximum speed or the crossed out symbol of degree of the prevention 2 if the maximum speed preliminary was not programmed.
  4. For change of speed press the top or bottom party of the screen wiper established in the handle () the switch of functions. Thus occurs stage-by-stage (one stage of 10 km/h) increase or reduction of values.

Cancellation of the entered restriction of speed

 PERFORMANCE ORDER

  1. Switch off ignition.
  2. Press and release in a control panel button SNESK. Illumination of the counter of run and a digital watch joins.
  3. Press and keep not less than 2 seconds button SNESK. On the display there is an entered threshold value of the maximum speed.
  4. Press the button of dump established in the handle of a screen wiper () while on the display there will be no crossed out symbol of degree of the prevention 2.

In some seconds after process of programming or cancellation illumination of the counter of run and a digital watch is switched off.

The travelling computer

Introduction

The travelling computer analyzes and deduces on indication of value of the current and average expense of fuel, average speed, a course stock on fuel and time in a way.

Indication of the travelling computer: the current expense of fuel

The travelling computer analyzes and deduces the following information on display FIS:

  • Fuel stock on a course
  • Time in a way
  • The average expense of fuel
  • Average speed
  • The current expense of fuel

The information (a course stock on fuel, time in ways, the average expense of fuel, average speed and the current expense of fuel) is deduced on display FIS in the above-stated sequence. All indicators (a course stock on fuel, time in ways, the average expense of fuel, average speed and the current expense of fuel) are displayed in metric, and in certain export variants in English system of units.

Memory

The travelling computer is completed with two automatically working memories.

The travelling computer: a cell of memory 1

Indication of number of the included memory is deduced on the display in figure of negative display. Occurrence on figure 1 display means a conclusion of indication of the data of a single memory (memory 1). Occurrence on figure 2 display means a conclusion of indication of the data of the general memory (memory 2).

Single memory

In a single memory it is brought the information from the moment of inclusion of ignition till the moment of its deenergizing. At renewal of movement within 2 hours after ignition deenergizing to already brought information the new is added. At a break of movement more than 2 hours occur automatic deleting of the data of a memory.

The general memory

Automatic deleting of the data from memory of the general memory is impossible. It it differs from a single memory. Thanks to it you can establish a time interval of the analysis of the information or the data.

The dump button

The button of sample and conclusion to the display of indication of various parametres is established in the handle of management by a screen wiper.

The screen wiper handle: controls the travelling computer

And — the Switch of functions
In — the dump Button

Consecutive short pressing of button "Reset" carries out a choice of the following indication:

  • Single memory (a cell of memory 1)
  • The general memory (a cell of memory 2)
  • Navigation/telematika*
  • Display deenergizing

For sample of the given kinds of indication only press and at once release button "Reset". By pressing and button keeping one second (for example, value of the current expense of fuel) will be established zero value of the given indication.

Display of faults of the monitoring system of malfunctions appears also at the switched off display.

Using

Management of the travelling computer is carried out by two switches established in the handle of management by a screen wiper.

Choice of functions

 PERFORMANCE ORDER

  1. Press the top or bottom party of the switch of functions (A). There is a consecutive conclusion to indication of 5 functions of the travelling computer.

Information deleting

 PERFORMANCE ORDER

  1. Carry out function sample.
  2. Press and keep a minimum one second the dump button (Reset) (B).

The dump button it is possible to establish following zero values:

  • Time in a way
  • The average expense of fuel
  • Average speed of movement

The travelling computer works only at the included ignition. At ignition inclusion on indication last is deduced at the moment of deenergizing of ignition function. Short pressing of the switch of functions (A) or dump buttons (B) it is possible to disconnect also indication of a reminder on necessity of a break of movement.

At a detachment of plugs of the accumulator all values brought in memory are erased.

Course stock on fuel

The given indication helps at planning.

On the display there is an indication of a stock of a course in kilometres. The given indication shows, how many kilometres the car still can pass on the actual rest of fuel in the given mode of movement. The course stock on fuel is defined by the discrete values counted by steps on 10 km.

The expense of fuel on the last is accepted to a basis of calculations of a stock of a course of 30 km of a way. At more economic subsequent movement the course stock increases.

Time in a way

Time indication in a way reminds of necessity of a break for movement.

On indication time in a way with readout from the moment of last dump of the data of memory of a memory is deduced. At desire to begin time readout in a way since the certain moment clear memory button "Reset" pressing (B).

Single memory

If the movement break makes more than two hours there is an automatic dump of indication of time in a way.

The general memory

Value of time in a way remains at the switched off ignition. At movement continuation to it the subsequent time of movement is added.

Reminder on necessity of a break in movement

In two hours after a start of motion, irrespective of the programmed function, there is an automatic switching on time indication in a way. Blinking indication of a kind 2:00 reminds the driver of necessity to make a break in movement.

Short-term pressing the top or bottom party of the switch of functions or button "Reset", the given indication it is possible to switch off.

At continuation of movement or if the break makes less than 10 minutes in each next two hours the reminder on necessity will stop on rest to repeat with time indication in a kind way 4:00, 6:00 etc. At duration of a break more than 10 minutes occur to the switched off ignition dump of the data of readout of time in a way.

The average expense of fuel

The given indication helps at movement planning.

On display indication the average expense of fuel in litres on 100 km, calculated is deduced from the moment of last dump of the data of memory. By means of the given indication it is possible to choose the mode of movement corresponding to the optimum expense of fuel. At desire of definition of the average expense of fuel anew it is necessary to carry out dump of the data of memory by button "Reset" pressing. At journey of the first 30 m after dump on indication zero value is deduced.

Single memory

If the movement break makes more than 2 hours there is an automatic dump of the data of the average expense of fuel.

The general memory

At the switched off ignition value of the average expense of fuel remains in memory. At movement continuation the data of the subsequent expense is considered.

Average speed of movement

The given indication helps at movement planning.

On display indication average speed in the km/h, calculated is deduced from the moment of last dump of the data of memory. At desire of definition of average speed anew it is necessary to carry out dump of the data of memory by button "Reset" pressing.

Single memory

If the movement break makes more than 2 hours there is an automatic dump of the data of average speed.

The general memory

At the switched off ignition value of average speed remains in memory. At movement continuation the new data is considered also.

The current expense of fuel

Indication of the current expense of fuel helps to save fuel.

On indication value of the current expense of the fuel measured in l/100 of km is deduced. By means of the given indication it is possible to choose the mode of movement corresponding to the optimum expense of fuel.

The expense is calculated on each 30-metre site of a way. During a car stop indication of last of the calculated values remains.

If after engine start function of definition of the instant expense of fuel on the first 30-40 metres of a way on indication its average value is deduced is caused.

Menu indication (models with an independent heater)

Introduction

The central console: a menu command key

Through corresponding commands of the menu of your car there is a possibility of adjustment, inclusion and management (for example, an independent heater/fan *) separate functions. Besides, by means of the menu you can deduce the necessary information on display FIS indication. The device works only at the included ignition. Management is carried out by a key <Menu> the central console. The initial menu informs you concerning various kinds of indication of the display. Following kinds of indication are possible:

Einstellen — (adjustment, installation)

Abfragen — (inquiry)

Menu aus — (menu deenergizing)

Hilfe — (help)

Choice and input of commands of the menu

Key <Menu> and the rotary/press button of the central console it is possible to cause menu indication, to read out the data and to carry out adjustment.

The central console: function of the rotary/press button

Key functions <Menu> and the rotary/press button.

Menu call

 PERFORMANCE ORDER

  1. Press a key <Menu>.

Choice and adjustment

 PERFORMANCE ORDER

  1. Rotate the rotary/press button.

Input and acknowledgement

 PERFORMANCE ORDER

  1. Press the rotary/press button.

Rotation of the rotary/press button makes a choice of the menu/is possible change of parametres of adjustment. The chosen parametres are allocated with a red background.

Pressing of the rotary/press button carries out acknowledgement of the chosen command/input in system of the established parametres.

Indication kinds

The initial menu

Initial menu FIS gives the chance samples of 4 kinds of indication.

To four kinds of indication of the initial menu there correspond following functions:

Einstellen (adjustment, installation)

Standheizung/-luftung* (An independent heater/fan)

Uhr (hours)

Computer (computer)

Tempoalarm (Geschwindigkeitswarnung) (the alarm system of excess of speed)

Abfragen (inquiry)

Service (maintenance service), see Has undressed Controls and devices.

Menu aus (menu deenergizing)

On the display there is a usual indication, as well as on cars without menu indication.

Hilfe (help)

The given function will help you to choose and enter necessary commands correctly.

Call of the auxiliary menu

FIS possesses help function.

Menu Hilfe (help)

Help function is caused as follows:

 PERFORMANCE ORDER

  1. Press a key <Menu>. There is an initial menu.
  2. Rotation of the rotary/press button choose function Hilfe (help).
  3. Confirm sample by pressing of the rotary/press button.
  4. For an exit from the auxiliary menu again press the rotary/press button.

Menu Hilfe (help) serves only for the information. Adjustment in the given menu is not represented possible.

Value of symbols of the display:

Symbol

The chosen function
Red background (function is switched off)

The command is chosen

The command is not chosen

The previous page

The following page

Adjustment process (a part 1)

Adjustment is carried out through menu commands.

The display: menu Einstellen, it is chosen Computer

Adjustment process is carried out as follows:

 PERFORMANCE ORDER

  1. Press a key <Menu>. There is an initial menu.
  2. Rotation of the rotary/press button choose a line Einstellen (adjustment).
  3. Confirm sample by pressing of the rotary/press button. There is a menu list.
  4. Rotation of the rotary/press button choose an actual line (a red background).
  5. Confirm sample by pressing of the rotary/press button.
  6. For correct installation of an arrow of sample of commands using symbols (the following page) or – (the previous page) can be demanded. Confirm it also with pressing of the rotary/press button.

At sample and acknowledgement by pressing of the rotary/press button of menu Computer there are two levels of menu Computer (Computer 1 and Computer 2). It is necessary for you to choose and confirm again with the rotary/press button, corresponding level.

Continuation, see the Part 2

Adjustment process (a part 2)

Menu Computer 1, the line Reichweite (a course stock on fuel) is chosen

Continue adjustment process as follows:

 PERFORMANCE ORDER

  1. Rotation of the rotary/press button choose an actual line (a red background).
  2. The chosen function joins installation in a tick small square ("yes"), and is switched off убиранием ticks (no").
  3. For return on higher level of the menu establish an arrow of sample of commands on Zuruck (back) and press the rotary/press button.

For some kinds of adjustment input of numerical values is required, for example, at date installation. It also is carried out by rotation of the rotary/press button.

Functional example (a part 1)

The resulted example shows the full process of adjustment which are carried out through commands of the menu.

The initial menu, the line Einstellen is chosen

Menu Einstellen, the line Uhr is chosen

If you wish to establish, for example, calendar date for this purpose it is necessary:

 PERFORMANCE ORDER

  1. Press a key <Menu>. There is an initial menu.
  2. Rotation of the rotary/press button establish a line of sample on Einstellen (adjustment).
  3. Confirm sample by pressing of the rotary/press button. There is a list will change Einstellen (adjustment).
  4. Rotation of the rotary/press button establish a line of sample on Uhr (hours).
  5. Confirm sample by pressing of the rotary/press button. There is a menu options Uhr (hours).

Continuation, see the Functional example (часть2).

Functional example (a part 2)

Menu Uhr, the line Datum is chosen

Continue process of adjustment of date as follows:

 PERFORMANCE ORDER

  1. Rotation of the rotary/press button establish a line of sample on Datum.
  2. If before line Datum there is an empty small square, press the rotary/press button. Now in a small square there should be a tick. Indication of last established date is deduced.
  3. Rotation of the rotary/press button include function of indication of date and press the rotary/press button. Date indication starts to blink.
  4. Rotation of the rotary/press button to the left or to the right establish correct numerical value of day. Press the rotary/press button. Indication of month now blinks.
  5. In the same way establish if necessary month and year.

Continuation, see the Functional example (a part 3).

Functional example (a part 3)

For an exit from the menu of adjustment of date the following is necessary:

 PERFORMANCE ORDER

  1. Rotation of the rotary/press button establish a line of sample on Zurck (back).
  2. Press the rotary/press button. Again there is menu Einstellen (adjustment).
  3. Again press the rotary/press button. Again there is an initial menu.