Audi A4, S4

Since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Controls and receptions of safe operation
+ Current leaving and service
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
- Suspension bracket and steering
   Security measures at work
   - Suspension bracket of forward wheels
      The general data
      Removal and installation of an amortisation rack
      Removal and installation of the shock-absorber/dismantling of an amortisation rack
   + Suspension bracket of back wheels
   + Corners of installation of wheels of the car
   + Steering and safety pillows
+ Body
+ Onboard electric equipment



Removal and installation of the shock-absorber/dismantling of an amortisation rack

Elements амортизационой racks

1 — the Nut with a fillet, 50Нм, self-stopped, necessarily replace
2 — a shock-absorber Support
3 — the Washer
4 — the Support
5 — the Screw spring

6 — the Additional spring
7 — the Protective casing
8 — the Protective cap
9 — a spring Support bottom
10 — a spring Plate bottom
11 — the Shock-absorber

Removal

 PERFORMANCE ORDER

  1. Remove амортизационую a rack.
  2. The amortizatsionaja rack can understand only with application of the special tool.

The spring амортизационой racks is compressed by the big effort. For shock-absorber removal it is necessary to compress a spring the special adaptation.

At all do not remove the shock-absorber if the spring reliably is not compressed. At installation of the adaptation for spring compression watch that spring coils have been reliably captured also the adaptation could not slide off. The spring is compressed by the big effort. Apply only the reliable tool. At all do not connect a spring a wire. Danger of accident!

  1. Clamp a spring with a tip in a vice.
  1. Compress a spring the corresponding adaptation. HUNDRED AUDI apply to this purpose adaptation V.A.G 1752/1 (1).
  1. At compression watch correct position of a spring in the adaptation (an arrow on an accompanying illustration). (1) – the adaptation for compression, (2) – a support for spring coils.
  1. Compress a spring so that the top plate was released.
  2. Turn away a nut with a fillet of fastening of a rod. Thus keep a rod from проворачивания a face key for internal шестигранника. The special tool (2, 3 and 4), shown on an illustration 4.3 (HAZET 4910/13 or AUDI-Т10001/7, Т10001/11 and Т10001/3) is For this purpose necessary.
  3. Remove the compressed spring together with the adaptation for compression.
  1. Remove a protective casing (1) and the bottom support of a spring (2).
  1. Mark position of the bottom plate in relation to the shock-absorber (4).
  2. Disconnect a plate (3) by means of a plastic hammer and remove upward.

Installation

There are springs of various groups of the admission. It is necessary to apply only springs with an identical colour label. It is recommended to replace springs and shock-absorbers in steam, i.e. from both parties of the car.

 

 PERFORMANCE ORDER

  1. Clamp a new cartridge of the shock-absorber with a tip in support амортизационой racks or in a vice with overlays.

  1. Transfer on the new shock-absorber a label from the old. Cautiously by means of a plastic hammer establish the bottom plate of a spring against the stop on the shock-absorber. Thus watch that the label on a plate has coincided with a label on the shock-absorber.

    And — A shock-absorber Axis / the bearing lever
    I — Left амортизационая a rack,
    In = 65 2
    II — Right амортизационая a rack,
    With = 87 2

  1. Position of the bottom plate is defined by the sizes specified in illustrations.
  2. The cut of a plate (arrow) should provide access to a body.
  1. Establish into place the bottom support of a spring and a protective casing.
  1. Establish into place compressed spring together with the adaptation for compression. The end of a coil of a spring should adjoin to an emphasis.
  1. Establish a support of the shock-absorber with the top support of a spring on the compressed spring so that the spring support adjoined to the end of a coil of a spring (the marksman on an accompanying illustration). The deviation in limits 2 is supposed.
  1. Establish a washer and a shock-absorber support.

Watch that the spring end adjoined to an emphasis of the top support of a spring.

  1. Tighten a new nut with a fillet the special tool the moment 50Нм. A spring yet do not unclench.
  2. Press vertically амортизационую a rack the adaptation for compression V.A.G 1752/2.
  1. Release the bottom lock lever and turn the top plate of a spring so that the support scale амортизационой racks stood on a mark 7 .
  1. Watch that the spring ends adjoined to an emphasis of the top and bottom support of a spring.

    I — At the left in a movement direction
    II — On the right in a movement direction
    And — a shock-absorber Axis / the bearing lever
    B — an installation Corner

  1. Fix the lock lever.
  2. The lever of a support of a spring of adaptation V.A.G 1752/2 (arrows) should coincide with the support centre.
  3. Cautiously ослабьте the adaptation for compression of a spring also take out it.
  4. Check up adjustment. If necessary, repeat procedure.
  5. Establish into place амортизационую a rack, address to corresponding section.