Audi A4, S4

Since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Controls and receptions of safe operation
+ Current leaving and service
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   The general data and security measures at carrying out кузовных works
   Cleaning and leaving
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   - The external equipment
      Installation of the forward panel in position for maintenance service
      Removal and installation of a cover of a water modular compartment
      Removal and installation of a forward bumper
      Removal and installation локера a back wing
      Removal and installation локера a forward wing
      Removal and installation of a forward wing
      Removal and installation of a back bumper
      Removal and cowl installation/adjustment
      Removal and installation of a cable of a drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and door installation
      Door adjustment
      Removal and installation of a frame of a window of a forward door
      Removal and installation стеклоподъёмника
      Removal and installation of the electric motor of a drive стеклоподъёмника
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a cover of a luggage carrier
      Removal, installation and adjustment of a cover of a luggage carrier
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Versatile person)
      Removal and installation of a door of a back (Versatile person)
      Removal and installation of the lock of a door of a back (Versatile person)
      Removal and installation of an external mirror
      Removal and installation молдингов
      Removal, installation and check сдвижной roof panels
      Removal and overlay installation сдвижной roof panels
      Check and starting position adjustment сдвижной roof panels
      Removal and sealant installation сдвижной panels
      Replacement of elastic bands of brushes of a screen wiper
      Removal and jet installation стеклоомывателя a windscreen
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of a cleaner of a windscreen
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets фароомывателя
      Adjustment of levers of a screen wiper
   + The salon equipment
+ Onboard electric equipment



Removal and installation of the lever of a cleaner of a windscreen

Removal

 PERFORMANCE ORDER

  1. Moisten a windscreen with water.
  1. Include quickly a screen wiper and switch off its switch. Thus the screen wiper stops in extreme position.
  1. Note on glass position of brushes at correctly established levers, for example, by means of a sticky tape.
  1. Open a cowl.
  1. Hook a screw-driver and uncover (3), (1) – скобы; (5) – a spoiler lattice.
  1. Turn away a nut (4) approximately on 2 turns, without turning on it completely. Slightly move the lever (2) so that it has separated from an axis. Turn away a nut completely and remove the lever from an axis. It is possible to apply to this purpose also a special stripper, for example, HAZET 1966-05.

If the lever hard acts in film, hook its wrench and cautiously remove.

Installation

 PERFORMANCE ORDER

  1. Check up, that the screen wiper electric motor stood in extreme position. If necessary, quickly include the electric motor and switch off the switch.
  1. Establish the lever on an axis of a screen wiper and expose it by means of a label put in the form of a sticky tape. It is possible to expose also the lever on distance between a brush and a spoiler lattice, having measured it from the right top of a cleaner

    Sedan/versatile person
    And = 26 mm
    b = 45 mm
    Cabriolet:
    And =24 5 mm
    b = 35 5 mm

  1. Screw a nut and tighten it by hand.
  1. Check up extreme position of levers. For this purpose close a cowl, moisten glass with water and quickly include a screen wiper. Screen wipers should return to the adjusted extreme position and the glass edge should not fall outside the limits. If necessary, turn away a nut and again adjust position of screen wipers.
  1. Tighten nuts the moment 21Нм. Establish to the place of a cover of levers.