Audi A4, S4

Since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Controls and receptions of safe operation
+ Current leaving and service
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   The general data and security measures at carrying out кузовных works
   Cleaning and leaving
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   - The external equipment
      Installation of the forward panel in position for maintenance service
      Removal and installation of a cover of a water modular compartment
      Removal and installation of a forward bumper
      Removal and installation локера a back wing
      Removal and installation локера a forward wing
      Removal and installation of a forward wing
      Removal and installation of a back bumper
      Removal and cowl installation/adjustment
      Removal and installation of a cable of a drive of a cowl
      Removal and installation of a clamp of the lock
      Removal and installation of facing of a forward door
      Removal and installation of facing of a back door
      Removal and door installation
      Door adjustment
      Removal and installation of a frame of a window of a forward door
      Removal and installation стеклоподъёмника
      Removal and installation of the electric motor of a drive стеклоподъёмника
      Removal and installation of the lock of a door
      Removal and installation of the handle of a door
      Removal and installation of the cylinder of the lock of a door
      Removal and installation of facing of a cover of a luggage carrier
      Removal, installation and adjustment of a cover of a luggage carrier
      Removal and installation of the lock of a luggage carrier
      Removal and installation of facing of a door of a back (Versatile person)
      Removal and installation of a door of a back (Versatile person)
      Removal and installation of the lock of a door of a back (Versatile person)
      Removal and installation of an external mirror
      Removal and installation молдингов
      Removal, installation and check сдвижной roof panels
      Removal and overlay installation сдвижной roof panels
      Check and starting position adjustment сдвижной roof panels
      Removal and sealant installation сдвижной panels
      Replacement of elastic bands of brushes of a screen wiper
      Removal and jet installation стеклоомывателя a windscreen
      Removal and installation of a jet of a washer of back glass
      Removal and installation of the lever of a cleaner of a windscreen
      Removal and installation of the lever of a cleaner of back glass
      Removal and installation of jets фароомывателя
      Adjustment of levers of a screen wiper
   + The salon equipment
+ Onboard electric equipment



Removal and installation of the lever of a cleaner of back glass

The versatile person

Removal

 PERFORMANCE ORDER

  1. Stop a screen wiper in extreme position.
  1. Mark brush position on glass, for example, by means of a sticky tape.
  1. Cautiously hook and uncover (4) a cleaner axis upwards.
  1. Cautiously remove a jet (3) from a connecting tube.
  1. Loosen the a nut (2) also remove the lever (5) from an axis. (6) – a brush.

Installation

 PERFORMANCE ORDER

  1. Check up, that the screen wiper electric motor stood in extreme position. If necessary, quickly start the electric motor and stop its switch.
  2. Establish the lever on an axis of a screen wiper and will expose it by means of a label put at removal. It is possible to expose also the lever on distance between a brush and the bottom edge of glass, having measured it from the right top of a cleaner. The adjusting size: from 15 to 20 mm.
  3. Screw a nut and tighten it by hand.
  4. Check up extreme position of the lever, if necessary, again adjust.
  5. Tighten a nut the moment 12Нм and close its cover.