Audi A4, S4

Since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Controls and receptions of safe operation
+ Current leaving and service
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
- Body
   The general data and security measures at carrying out кузовных works
   Cleaning and leaving
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   + The external equipment
   - The salon equipment
      Remarks on work with the salon and security measure equipment
      Removal and installation of spring clips
      Removal and installation of the central console
      Removal and installation of the holder of drinks
      Removal and installation of facing of the lever of a lay brake
      Removal and installation of a cover of the lever of switching of transfers/selectors
      Removal and ashtray installation
      Removal and installation of the central armrest
      Removal and installation of an internal mirror
      Removal and cover installation on a control panel
      Removal and pocket installation from outside the driver
      Removal and installation of a ware box
      Removal and installation противосолнечного a peak
      Removal and installation of facing of a rack And
      Removal and installation of the top facing of a rack In
      Removal and installation of the bottom facing of a rack In
      Removal and installation of a forward overlay of a threshold
      Removal and installation of facings (Sedan)
      Removal and installation of facings (Versatile person)
      Removal and installation of a forward seat
      Removal and installation of a back seat
      Removal and installation of a forward seat belt
      Removal and installation of a back seat belt
+ Onboard electric equipment



Removal and installation of facings (Versatile person)

Rack With

Removal

 PERFORMANCE ORDER

At a detachment of cables of system of a pillow of safety necessarily observe security measures at the reference with a safety pillow, address to Section the General data and security measures.

  1. To exclude operation a pillow of safety of a head, switch off ignition and disconnect at first negative (-), and then positive cables of the storage battery. Instructions are resulted in Section Replacement of the storage battery.
  2. Remove a lateral pillow of a back seat, address to Section Removal and installation of a back seat.
  3. Remove lateral facing of a luggage carrier, address to corresponding Section.
  4. Remove facing over a back door.
  5. Loosen the screws of fastening of a pillow of safety of a head in a back part.
  6. Remove directing for a back belt, address to Section Removal and installation of a back seat belt.
  1. Turn out screws (3), disconnect facing (1) at a spring clip (2) and remove.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, return to removal. Thus fix a pillow of safety of a head new screws.
  2. Put a door sealant over facing.

During joining of the storage battery in salon there should not be people.

  1. Remove изоляционную a tape from the negative plug of the storage battery, attach at first positive (+), and then a negative cable (-) to a battery accumulator room.

Observe instructions Replacement of the storage battery Has undressed.

Facing over a back door

Removal

 PERFORMANCE ORDER

At a detachment of cables of system of a pillow of safety necessarily observe security measures at the reference with a safety pillow, address to Section the General data and security measures.

  1. To exclude operation a pillow of safety of a head, switch off ignition and disconnect at first negative (-), and then positive cables of the storage battery. Instructions are resulted in Section Replacement of the storage battery.
  2. Disconnect facing behind a rack And.
  3. Remove facing of rack D.
  1. Press downwards the handle (5) and cast away downwards a cover of the screw (4). For this purpose enter into a groove (7) thin wire and open a cover.
  1. Turn out screws (3).
  2. Turn out the screw (1).
  3. Turn out the screw (7) for what displace back a lath in an eye for a dividing grid.
  4. Disconnect facing (2) at a spring clip (6) and remove.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, return to removal, thus the screw (7) tighten the moment 9Нм.

During joining of the storage battery in salon there should not be people.

  1. Remove изоляционную a tape from the negative plug of the storage battery, attach at first positive (+), and then a negative cable (-) to a battery accumulator room.

Observe instructions Replacement of the storage battery Has undressed.

Rack D

Removal

 PERFORMANCE ORDER

At a detachment of cables of system of a pillow of safety necessarily observe security measures at the reference with a safety pillow, address to Section the General data and security measures.

  1. To exclude operation a pillow of safety of a head, switch off ignition and disconnect at first negative (-), and then positive cables of the storage battery. Instructions are resulted in Section Replacement of the storage battery.
  2. Remove closing lath of a roof, address to Section Removal and installation of facings (Sedan).
  3. Disconnect a back edge of lateral facing of a cargo compartment, address to corresponding Section.
  1. Turn out the screw (3) for what displace back a lath in an eye for a dividing grid.
  1. Disconnect facing (1) at two spring clips (2) and take out upwards from lateral facing of a cargo compartment.
  2. Take out facing of rack D (1) back from facing (4) over a door.
  3. Loosen the in a back part screws of fastening of a pillow of safety of a head.
  4. Turn out screws (6) and remove facing (5) over a back window.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence. Return to removal. Thus fix a pillow of safety of a head new screws.
  2. Put a sealant of a cover of a back over facing.

During joining of the storage battery in salon there should not be people.

  1. Remove изоляционную a tape from the negative plug of the storage battery, attach at first positive (+), and then a negative cable (-) to a battery accumulator room.

Observe instructions Replacement of the storage battery Has undressed.

Closing lath of a roof

Removal

 PERFORMANCE ORDER

  1. Disconnect closing lath of a roof (1) at four spring clips (2) and remove.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, return to removal.
  2. Put a sealant of a cover of a back over a closing lath of a roof.

Lateral facing of a cargo compartment

Removal

 PERFORMANCE ORDER

  1. Lateral facing right: Disconnect a negative cable (-) the storage battery.

Observe instructions Replacement of the storage battery Has undressed.

  1. Remove a lateral pillow of a back seat, address to Section Removal and installation of a back seat.
  2. Release a floor of a cargo premise and take out.
  3. Remove an overlay of a cargo compartment, see more low.
  1. Turn out screws (4) fastenings of an eye for luggage (5).
  1. Turn out the screw (3) and disconnect lateral facing (2) at spring clips (1).
  2. The right lateral facing: Disunite a socket socket.
  3. Take out lateral facing.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, return to removal.
  2. The right lateral facing: Attach a negative cable (-) the storage battery.

Observe instructions Replacement of the storage battery Has undressed.

Overlay of the lock of a cargo compartment

Removal

 PERFORMANCE ORDER

  1. Open a back door.
  1. Turn out 4 screws (1) and cautiously disconnect an overlay of the lock (2) from an edge of a compartment at lock fingers (the marksman on an accompanying illustration). Thus displace a plastic wedge under an overlay and each finger remove separately.

Installation

 PERFORMANCE ORDER

  1. Installation is carried out in sequence, return to removal.