Audi A4, S4

Since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Controls and receptions of safe operation
+ Current leaving and service
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Diagnostics of malfunctions of an onboard electric equipment - the general information
   Рассоединение sockets
   Check of the electric motor of a screen wiper
   Check of warmed back glass
   Check of stoplights
   Removal and installation of a sound signal
   Removal and installation of gauges of a parking
   Replacement of the battery of a remote control of the ignition key
   The relay and safety locks
   Replacement of lamps накаливания devices of external illumination
   Removal and installation of headlights
   Removal and installation of the lateral repeater of turns
   Removal and installation of an additional stoplight
   Removal and installation of a back lantern
   Removal and installation of a lantern of illumination of licence plate
   Removal and installation of plafonds of internal illumination
   Removal and control panel installation
   Removal and installation подрулевого the switch
   Removal and installation of switches of a forward door
   Removal and installation of the switch of light
   Removal and switch installation стеклоподъёмника in a back door
   Removal and installation of the switch of a cover of a luggage carrier
   Removal and installation of the switch of a lay brake
   Removal and installation of the switch of illumination of a ware box
   Removal and installation of switches of the central console
   Removal and radio receiver installation / the navigating device/CD-changer
   Removal and installation of loudspeakers
   Removal and installation of aerials
   Removal and installation of the tank of a liquid of the stekloomyvatelja/electric motor of the pump
   Removal and installation of the electric motor of a cleaner of a windscreen
   Removal and electric motor installation on back glass (Versatile person)
   The uniform lock - the general information
   Removal and installation запорного an element of a cover of a fuel tank
   The digital tyre of given CAN
   + Basic schemes of an electric equipment



Removal and installation of a back lantern

Sedan

Removal

 PERFORMANCE ORDER

  1. Open an aperture (1) in luggage carrier facing.
  1. Turn out the screw (3) and cast away a back lantern outside, having taken out thus from a wing a spherical finger.
  1. Disunite a socket on the lamp panel.

Installation

 PERFORMANCE ORDER

  1. Join a socket on the lamp panel.
  1. Establish a back lantern on a body so that fingers were pressed into plugs (7). Thus watch correct position of consolidation.

    1 — The Dimensional lantern
    2 — Stop-signal a lantern
    3 — The turn Index back
    4 — A backing Lantern
    5 — The Foggy lantern
    6 — The Connecting tip
    7 — Plugs

  1. Tighten the screw (3) moment 6Нм.
  1. If it is necessary, turn away a nut (2) and will expose a back lantern so that to provide a uniform backlash in relation to adjoining with body parts. A nut tighten the moment 12Нм.

Replacement of lamps накаливания

 PERFORMANCE ORDER

  1. Compress 2 lock laths (arrow) and remove from a back lantern the lamp panel.

    1 — the Dimensional lantern
    2 — Stop-signal a lantern
    3 — the turn Index back
    4 — a backing Lantern
    5 — the Foggy lantern
    6 — the Connecting tip
    7 — Plugs

  1. Press lamps with (1) on (5) into cartridges, turn and take out. Replace lamps with the new.

If the lamp of a lantern of a backing after replacement all the same does not burn, it is necessary to check up the switch. The switch is on a check point over a power shaft flange.

The versatile person

Removal

 PERFORMANCE ORDER

  1. Open a door of a back and take out from facing заглушку.
  1. Turn out a bolt (1). Cast away a back lantern outside, having taken out thus a spherical finger from a wing.
  1. Disunite a socket of the lamp panel.

Installation

 PERFORMANCE ORDER

  1. Join a socket of the lamp panel.
  1. Establish a back lantern on a body so that fingers were pressed into epiploons (6). Thus watch correct position of consolidation.

    1 — The Foggy lantern
    2 — The turn Index back
    3 — A backing Lantern
    4 — Stop-signal fire
    5 — The Connecting tip
    6 — Plugs for fingers

  1. Tighten the screw (1) moment 6Нм.
  1. If it is necessary, turn away a nut (2) and will expose a back lantern so that to receive a uniform backlash in relation to adjoining elements of a body. A nut tighten the moment 12Нм.

Replacement of lamps накаливания

 PERFORMANCE ORDER

  1. Press four lock laths outside of (arrows on an accompanying illustration) and remove the lamp panel from a back lantern.
  1. Press lamps накаливания with (1) on (4) into cartridges, turn and take out. Replace lamps with the new.

    1 — the Foggy lantern
    2 — the turn Index back
    3 — a backing Lantern
    4 — Stop-signal fire
    5 — the Connecting tip
    6 — Plugs for fingers

If the lamp of a lantern of a backing after replacement all the same does not burn, it is necessary to check up the switch. The switch is on a check point over a power shaft flange.