Audi A4, S4

Since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Controls and receptions of safe operation
+ Current leaving and service
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Diagnostics of malfunctions of an onboard electric equipment - the general information
   Рассоединение sockets
   Check of the electric motor of a screen wiper
   Check of warmed back glass
   Check of stoplights
   Removal and installation of a sound signal
   Removal and installation of gauges of a parking
   Replacement of the battery of a remote control of the ignition key
   The relay and safety locks
   Replacement of lamps накаливания devices of external illumination
   Removal and installation of headlights
   Removal and installation of the lateral repeater of turns
   Removal and installation of an additional stoplight
   Removal and installation of a back lantern
   Removal and installation of a lantern of illumination of licence plate
   Removal and installation of plafonds of internal illumination
   Removal and control panel installation
   Removal and installation подрулевого the switch
   Removal and installation of switches of a forward door
   Removal and installation of the switch of light
   Removal and switch installation стеклоподъёмника in a back door
   Removal and installation of the switch of a cover of a luggage carrier
   Removal and installation of the switch of a lay brake
   Removal and installation of the switch of illumination of a ware box
   Removal and installation of switches of the central console
   Removal and radio receiver installation / the navigating device/CD-changer
   Removal and installation of loudspeakers
   Removal and installation of aerials
   Removal and installation of the tank of a liquid of the stekloomyvatelja/electric motor of the pump
   Removal and installation of the electric motor of a cleaner of a windscreen
   Removal and electric motor installation on back glass (Versatile person)
   The uniform lock - the general information
   Removal and installation запорного an element of a cover of a fuel tank
   The digital tyre of given CAN
   + Basic schemes of an electric equipment



Removal and installation of the electric motor of a cleaner of a windscreen

Removal

 PERFORMANCE ORDER

  1. Open a cowl and uncover over a water modular compartment, address to Section Removal and installation of a cover of a water modular compartment.
  2. Remove screen wiper levers, address to corresponding Section.
  3. Disconnect a negative cable (-) the storage battery.

Observe instructions Replacement of the storage battery Has undressed.

  1. Remove скобы (1), pull forward a lattice of a spoiler (5) and remove it. (2) – the cleaner lever, (3) – a cover; (4) – a nut.
  1. Turn out screws (arrows) and uncover boxes of the block of management.
  1. Remove by means of squeezing lever AUDI 80-200 or the big screw-driver of a bar (2) from a spherical head.
  1. Mark with a felt-tip pen crank position on an assembly plate (1) engines.
 
  1. Turn away a nut and remove a crank (1) from the cleaner electric motor.
  1. Disconnect directing for a wire and a hose from a cleaner framework.
  2. Turn out screws of fastening (arrow) and take out a framework of a cleaner with the electric motor.
  3. Disunite an electric motor socket.
  4. Turn out three screws of fastening (arrow) and remove the electric motor from a framework.

Installation

 PERFORMANCE ORDER

  1. Fix the electric motor without a crank on a cleaner framework. Screws tighten the moment 9Нм.
  2. Join an electric motor socket.
  3. Insert a framework with the electric motor into an impellent compartment and fix the moment 8Нм.
  4. Stop the electric motor in extreme position for what quickly switch on and off the cleaner switch.
  5. Establish a crank (1) at an angle a = 2 on a shaft of the electric motor and fix it. Tighten a nut (2) moment 18Нм.
  6. The further installation is carried out in sequence, return to removal.