Audi A4, S4

Since 2000 of release

Repair and car operation



Audi A4, S4
+ Introduction
+ Controls and receptions of safe operation
- Current leaving and service
   Specifications
   The indicator of term of approach of maintenance service
   The routine maintenance schedule
   The general information on adjustment
   Check of levels of liquids, the control of leaks
   Check of a condition of tyres and pressure in them. A designation of tyres and disks of wheels. Rotation and replacement of wheels
   Replacement of impellent oil and the oil filter
   Checks of brake system. Adjustment of a lay brake
   Check of fuel system
   Check of a condition and replacement of hoses of an impellent compartment, localisation of leaks
   Check of a condition of ridge belts of a streaming drive of auxiliary units
   Check of functioning of system of cooling and frost resistance of a cooling liquid
   Check of a condition of system of release of the fulfilled gases
   Check of level of oil of automatic transmission
   The visual control of a box of a gear change and the main transfer on leaks, check of level and oil addition
   Check of a condition a suspension bracket and steering component
   Check of a condition of protective covers of power shafts
   Check of level of a liquid of system of hydrostrengthening of a wheel
   Check of a central air of air
   Greasing of terminators of doors, cylinders of locks, cowl hook, сдвижной panels of the hatch of a roof
   The visual control of a seat belt and the block of a pillow of safety
   Check of working capacity of headlights and horn
   Condition check, adjustment and replacement of brushes of screen wipers
   Check of a condition of the battery, care it and gymnastics
   Replacement of the battery of emergency supply of system Telematik
   Replacement of an element of the filter of air of salon / the coal filter of clearing of air
   Replacement of a brake liquid
   Check and replacement of spark plugs. Check of a condition of high-voltage wires
   Replacement of an element of the air filter of the engine
   Replacement of the fuel filter
   Check of a condition and tension of a gear belt
+ The engine
+ Systems of cooling, heating and the air conditioner
+ Power supply systems, release and decrease in toxicity of the fulfilled gases
+ Systems of an electric equipment of the engine
+ Manual box of a gear change
+ Automatic transmission
+ Coupling, power shafts and differential
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



The visual control of a box of a gear change and the main transfer on leaks, check of level and oil addition

For search of places of leaks:

 PERFORMANCE ORDER

  1. The diesel engine: remove the bottom cover of the engine, address to Section Removal and installation of the top cover of the engine / the bottom protection of an impellent compartment/stretcher.
  2. Clear the transmission case a cold cleaner.
  3. Strew possible places of leaks известью or a talc powder.
  4. Pass on the car. That oil became liquid, pass on a high-speed line distance about 30 km.

Operation of lifting and car installation on supports is connected with danger! Therefore before operation carrying out familiarise with Razdelom Poddomkrachivanie and towage.

  1. Lift and establish the car on supports. Shine with a lamp a transmission and check up places of leaks.
  2. At once eliminate leaks.
  3. The diesel engine: Establish the bottom cover of the engine, address to Section Removal and installation of the top cover of the engine / the bottom protection of an impellent compartment/stretcher.

Check of level and oil addition

The special tool:

  • Viewing hole or jack with supports.
  • For отворачивания stoppers for filling of system with oil depending on execution:
    • шестигранный a face key on 10 mm, for example, HAZET 985-10;
    • Many-sided face key on 16 mm, for example, HAZET 2567-16 or AUDI 3357.
    • The thin wire, which end in length of 1 sm is unbent on 90 , for measurement of level of oil.

 PERFORMANCE ORDER

  1. Establish the car over a viewing hole or lift horizontally on supports.
  2. Remove the bottom cover of the engine, address to Section Removal and installation of the top cover of the engine / the bottom protection of an impellent compartment/stretcher.
  3. The stopper for заливания oils is on a check point before the left power shaft and can be closed the heat-shielding screen of a shaft. In this case it is necessary to disconnect the heat-shielding screen.
  1. Turn out a stopper for заливания oils a face key for internal шестигранника on 10 mm or a key under an internal polyhedron 3357.
  1. Models with a forward drive and a check point 012/01W: To the control of level of oil apply the index of own manufacturing described above with the unbent end. For the control of level the index hold in an aperture horizontally, unbent end should look downwards. Take out the index and check up oil level under the index. Oil level correct if it is on 7 mm below an aperture.
    1 — Oil in a check point
    2 — the Index of level of oil of own manufacturing
    3 — Carter of a check point
  1. Models with a 5-step full drive (01А), and also with 5 and a 6-step forward drive (01Е): oil Level should reach the bottom edge of an aperture under a carving stopper.
  2. Models with a 6-step full drive (01Е): oil Level should be on 1 1 mm below an aperture under a carving stopper.

If oil level too low, check up a box on tightness, if necessary, repair (work HUNDRED). It is Not enough to fill in oil only. It is necessary to observe the established level of oil! In no event it is impossible to pour oil.

  1. If a check point it is tight, fill in oil. Tighten a stopper the moment specified in Specifications.
  2. Fix the heat-shielding screen on a check point if he acted in film.
  3. Establish into place a cover of an impellent compartment, address to Section Removal and installation of the top cover of the engine / the bottom protection of an impellent compartment/stretcher.

Differential of a back axis, model quattro

Check of level of oil of differential is made at отворачивании stoppers for filling with oil (marksman). Oil level should reach the bottom edge of a carving aperture.

Tighten a stopper the moment specified in Specifications.